Gao Fei didn't relax for a moment. Since he had already made a decision, he had to take action. First, he had to make the blower first. This is not difficult at the moment, just install the fan blades.

Of course, although it is just a small fan blade, this is still not a very simple thing. The main reason is that the 913 outpost is too poor and there are really not many things to find available.

Gao Fei did not take out the steel bars in the stove, so he left it in the stove and continued to burn it, leaving the kitchen and coming to the warehouse, intending to find something to use from the warehouse.

Finally, Gao Fei found an oil pot. Although he usually thought that the oil pot might have a lot of space, now it has to be removed to make the fan blades he needs.

Without scissors, it would not be so easy to cut the oil pot properly. At least now, Gao Fei must have a handy tool to pick up the needed fan blades.

There is no way. At present, there are not many powerful tools that can be used at the 913 outpost, including an axe, a kitchen knife, and a saw.

Whether the saw can be used should be able to use it, but Gao Fei is not sure. At least with his current hands-on ability, he cannot use the saw to see the oil pot. The plastic is as fine as the mark.

And the axe is really unable to do fine homework on plastic. After all, what the axe needs to do is a more violent and rough job.

So in summary, the tool that Gao Fei can use is the kitchen knife. Although it is not the best tool for making fan blades, Gao Fei has no choice either. Who made the 913 outpost so poor that there were not even scissors?

Gao Fei took the oil pot to the kitchen. He took a kitchen knife and pressed it downwards, opening a gap on one side of the oil pot. Gao Fei later discovered that breaking the plastic was not an easy task.

Without scissors, it is necessary to use a kitchen knife to open the seam. You need to be very slow. You can master the direction of the kitchen knife. Otherwise, you will cut it down like he did at the beginning and make half of the seam.

However, this is still a relatively easy thing for Gao Fei to accept. After all, there is more than one oil pot in the warehouse. If you break one, you can get one for use.

"I'm still not serious enough in doing things!" Gao Fei sighed. Fortunately, the fan blade he wanted to make didn't need to be very big. The four sides of the oil pot would have little impact on him.

Although Gao Fei made a mistake in the first place, this also gave him a chance to improve. Isn’t it said that failure is a success? A failure is also a accumulation of experience. If you do it next time, you will not make the previous mistakes.

Gao Fei practiced a kitchen knife here, and looked down from the mouth above the oil pot. This time he was very slow and held the direction of the kitchen knife with both hands. This time he finally succeeded. Although the crack that Gao Fei made was not straight, the general direction was not wrong.

With the first time, there will be a second time. Gao Fei has a kitchen knife here, and will support him to raise the other side, continue to rush up and cut down, and cut one side of the oil pot. This is a relatively flat plastic board.

However, the bottom was also connected to the oil pot, which made Gao Fei even more difficult. The two successes in the next two had already allowed Gao Fei to master the skills. His oil pot came over and placed the oil pot horizontally on the ground, pulled the flat plate apart, and almost at a right angle to the oil pot. Using a kitchen knife, he cut the side of the side of the pulling side against the bottom, and then cut it down bit by bit.

A relatively flat plastic board appeared in Gao Fei's hand. Now he could use this plastic board to make a fan blade. However, the plastic board Gao Fei was following is very large now, and the fan blade Gao Fei was going to make was really not that big. So he put the plastic board on the ground and compared a print from the middle. He took a kitchen knife and drew a piece along the print on it.

The kitchen knife did not cut the relatively flat plastic board. Gao Fei put the kitchen knife down and pulled the plastic board up. He pulled it hard along the gap made by the kitchen knife in the middle and pulled it hard to both sides. As a result, he found that he still overestimated his strength. The relatively flat plastic board was not torn open from the middle by him.

Gao Fei looked at the plastic board again, then he squeezed the opposite sides of the gap together, finally put the edges of the two sides together, and squeezed them out of the middle. Finally, he folded the relatively flat plastic board together.

Although this has been achieved, the plastic board has not been completely broken into two parts, and the middle is still connected.

Gao Fei folded the plastic board that he had chased the most again, and he didn't know if it had been broken a little, so Gao Fei continued to fold it in half. After folding it in half several times in a row, the plastic board was finally made into two halves by him.

But his success rate is very close. The two plastic boards in Gaofei's first class were combined together. The single piece was still too thin and the hardness was not enough. Gaofei thought that if the two plastic boards were combined, the fan blades made should be enough.

At present, there is no glue to glue these two plastic boards at the 913 outing, but for Gao Fei, it is not necessary to glue to mix them together. He has other methods.

Gao Fei took the wire over and put it in the stove. At this time, the steel bars in the stove were already burning red, but Gao Fei didn't care about it now. He had more important work to do. Gao Fei burned the wire in the stove for a while. Was he waiting for the one end of the wire to burn red? He asked me to give the explanation again.

Then he saw Gao Fei quickly put the burned iron wire into the middle of the two plastic boards. He pulled the iron wire out, and then stepped on the combined plastic boards. After three or five seconds, Gao Fei picked up the plastic board from his feet. When he saw that the two plates were fitted together very reasonably.

Gao Fei used the method of sticking plastic boards to stick to it was not thought of by himself. This was a method he had seen many parents use when he was young.

Gao Fei was very young at that time. Whenever it was summer, when children changed into plastic sandals, someone would wear them and break them. At this time, parents would try to save trouble. They took the burned metal and put the broken metal on both sides, then placed the burned metal in the middle and quickly pulled it over. The half-melted cross sections will be well stuck together.
Chapter completed!