The internal texture of the bearing, under the light, has nothing like the texture it looks like on the drawing.

Under the reflection of light, the lines inside are like a big snake running, twisting and turning.

This is a bearing;

Big brother;

What the hell is that?

If this accessory is installed, Liu Chi can guarantee that the bearing will be out of service within three days without any discussion.

The entire bearing is the support point of the core component of the prism and is the magnetic field control center. If this thing cannot be built, then there is absolutely nothing to say about the prism, and you can just go to the side and take a nap.

You can go home and wash yourself and sleep.

What are bearings?

Bearings are the most common metal parts in modern industry and life. They are a core component that converts mechanical energy into kinetic energy. No matter what kind of machinery, they are basically one of the indispensable accessories.

And this time, it is the three magnetic field generation points of the entire prism.

Electricity expands the magnetic field!

Electron free magnetic field!!

Atoms induce magnetic field!!!

Although the requirements for this bearing are a bit too high, there are a total of 36x2=72 locking grooves of the same size on the front, back and both sides, and each groove is equipped with an assembly.

The front is a little better, there are 36 sets of assemblies, all of which are used to fire energy cannons.

The reverse side is a bit more complicated. There are 36 card slots, one of which is divided into three groups, each with 12 sets, corresponding to the electric expanded magnetic field, the electron free magnetic field, and the atomic induced magnetic field.

The requirements are very high.

There are 72 sets of assemblies in it, four groups of which are the core of the entire prism.

In fact, this bearing assembly is also the most difficult accessory of the entire prism.

...

half an hour later;

Liu Chi took off the newly machined bearing from the machine tool, took a deep breath, reached out from the operating table, and picked up a Callander 900x portable microscope.

Try again!

A portable microscope with its own light source is usually used to observe the surface of jewelry and the surface roughness of metal materials. It is only the size of a mobile phone and is very suitable for portability.

Liu Chi adjusted the resolution and light source, and aimed the lens of the portable microscope at the inner hole of the bearing.

After looking at it for three minutes, Liu Chi put down the bearing in his hand and moved his tired hands! It was strange that he was not tired when holding an object weighing about fifteen kilograms with one hand.

Liu Chi's face also became serious. Under the nine hundred times magnification, even though it looked curved just now, now he can actually see gaps appearing;

These gaps are at the edges of each slot.

Like a mouse gnawed it.

Although it is so small that it cannot be seen clearly, so when you look at it with the naked eye, you will feel that it is curved, but you cannot see where the problem is.

Only under the observation of 900 portable microscopes can we see clearly that there are gaps between the slots.

How thin are these gaps?

When you find a problem, you have to find a way to solve it. Before solving the problem, you must first find out the root cause of the problem so that you can prescribe the right medicine.

Liu Chi took the bearing to an ultra-high-precision laser interferometer and measured it. After some fiddling, the gap was basically only 0.2um, which was so small that it could not be seen with the naked eye.

...

After half an hour of fiddling, observing and measuring, and comparing the results several times, I finally found the answer!

The answer is that the metal material used in this bearing does not meet the requirements.

!!!

Material problem!

well!

Materials are the biggest headache for Liu Chi.

Liu Chi now feels like one head and two heads. It feels like playing a game. You want to meet the world boss the most, but you are so lucky, and you just meet it, blocking your way forward.

Ahhhh!!!

The accuracy problem is solved;

You have another question about materials

Is there any love left?

Come on!!!

Liu Chi almost cursed!

If the material is not solved, there is basically no way to start now. The material just now is already the most suitable for processing bearings;

Still not working.

Now it's completely blocked and I can't move!

...

Liu Chi sighed, put down the measuring tool in his hand, picked up his mobile phone from the table, swiped a few times on the screen, found Wang Shan's number, and called!

"Beep, beep, beep..."

After the ringtone rang several times, Wang Shanming's angry voice came from the phone: "Boss, I am Wang Shan?"

"Manager Wang, do you have any materials suitable for bearings? Do you want the best ones? Don't worry about the cost." After Liu Chi finished speaking, he added: "I want it ready-made, or you have a way to get it that you think is the best."

of."

"A bearing maker?"

"Yes, the higher the density, the better. The most important thing is that the lower the impurity content, the better. Now I can't use high carbon steel or chromium alloy steel, and the inside will be pitted after processing."

"Boss, if those two materials are not good, the materials I have now will probably not be much better?" Wang Shan asked after a while.

"Take a look at what you have on hand, or whatever you can get, get some samples over here, and I'll try them." At this time, Liu Chi had no choice but to become a live doctor.

"Okay, what specifications does the boss want?"

"The diameter of my bearing is 52mm, and the maximum is 23mm. When you arrange the rough parts, try to make them as large as possible."

"Okay, I'll arrange it right away and produce it as quickly as possible. I'll also ask some of my friends to see if they have anything suitable, and we'll send it over together when the time comes."

"Okay, hurry up on this, I'll wait for it." Liu Chi explained.

"OK."

"Do you have all the scientific research personnel in place now?" Liu Chi asked smoothly.

"Not yet. Recently, I have recruited a group of fresh graduates from universities across the country. Some of them are not yet in place. It will take another month to basically set up the scientific research system. If we want to form a combat effectiveness, it will probably take more than a month of running-in."

"..."

After 10 minutes, Liu Chi hung up the phone, put down the phone, and waited for Wang Shan to send some materials before trying again.

After that, I called Chen Luguang and asked the superiors to help me!

If it still doesn't work, you can only start with the materials.

In fact, the issue of materials was the last thing Liu Chi wanted to touch.

It feels like buying a lottery ticket. If you are lucky, you will win all of a sudden. If you are not lucky, it will be in vain after ten or eight years.

Let's do more research.

Liu Chi thought for a long time and thought of using a nanoscale coating to increase the hardness. Using plasma vapor deposition, a diamond grinding layer with a thickness of only a few nanometers could be coated.

But before I started taking action, I gave up.

Because it’s even more unreliable!

Because I don’t have the technology, not only can I not do it myself, but none of the domestic precision manufacturing companies can do it;

To have such a technology, it is a series of technologies. Now Liu Chi feels that he is as busy as a dog. If he develops a series of technologies again, people will not be able to survive. How can he have time to do it again?

Let’s talk about this later when we have a chance, I don’t have time to worry about it now.

I’ll put it aside for now and talk about it later when I have time...

...

Jingxin Group Conference Room!

Seating for five people.

Ye Jing, Jiang Yu, Zhang Handong, Yu Kang, and a small shareholder Luo Su.

"Everyone is here, let's start." Ye Jing glanced at the people present and continued: "We have called everyone here today because we have a plan to announce."
To be continued...